Hydraulic Busbar Processing Machine for Bending Punching Dies

DESAN PLC Hydraulic Copper Bus Processing Machine:

1. One layer of large board, thickened 200mm table top, strong load-bearing capacity

2. The second-layer slab is thickened by 35mm thickness

3. Φ60 hard shaft high temperature quenching hardness reaches 55 or more, more wear-resistant

4. Nodular cast iron integrated turret with six stations or eight stations is optional

5. Increase the shearing pressure by 50 tons of oil cylinder (large shearing force and smooth section)

6. 60*60*5(mm) square tube used for the large rack of the equipment, strong and stable

Copper Busbar Bending Machine

Heat dissipation hole

The small opening on the device is conducive to satisfying the isotropic heat dissipation in the box and giving full play to the role of heat dissipation.

Cable middle joint protection box

To prevent the voltage from being unstable and causing damage to the circuit and plc of the equipment, the equipment has a protective effect when the voltage is unstable.

Emergency protection button

The equipment has safety protection technical measures such as reliable grounding, residual current protection (leakage protection) 30mA 0.1S, anti-misoperation foot switch, and out-of-control protection (emergency stop).

Positioning of double gauges

The punching station is equipped with a two-way positioning device, which is suitable for mass production in the factory. It can realize the mechanical two-way positioning of the X axis and the Y axis. During the work process, the operator does not need to draw a cross line or punch a foreign punch, which improves the work efficiency and the accuracy of the punching position. 

Positioning pin

Positioning pin makes production and processing positioning more accurate

Laser positioning

The marking is accurate, intuitive and practical, stable, easy to operate, can improve work efficiency and reduce waste. The laser line is arbitrarily fine-tuned in the three-dimensional space to achieve the best use effect.

Cutting cylinder

The cutting unit adopts a double-column double-knife type cutting structure, and the upper knife and the lower knife are installed vertically and parallel to ensure that the cutting edge is flat, no waste, and no deformation after long-term use. Increase the shearing pressure by 50 tons.

Bending process

The bending station adopts a closed bending structure for reinforcement and durability. The flat bending, vertical bending and embossing are more uniform, and the U-shaped bending function can be realized. The minimum distance between the two bends is 40mm.

PLC-Siemens

The bending angle is controlled by PLC and displacement sensor in cooperation with each other, and it has storage memory and error compensation functions to ensure bending accuracy and angle consistency.

Limit bending

The positioning limit is automatically generated by the system after the parameter call screen is set, which is safe and convenient.

CNC bending

"Z-bend" can automatically calculate the required angle by inputting the vertical height (H) and the length of the hypotenuse (L) of the upper and lower planes. In the working process, you only need to input the corresponding angle and the thickness of the busbar used to process the workpiece conveniently and quickly.

DESAN Copper Busbar Bending Machine：

Leveling the foot pad

Automatic adjustment according to ground requirements to make the machine more stable

Fuel tank oil seal

To prevent debris from falling into the fuel tank and causing the valve to open

Pressure gauge

The pressure can be observed at any time, and can be pressurized or depressurized at any time according to the thickness of the copper bar

Stable voltage

Stable high and low potential free charge directional movement. Common voltages 220V, 350V, 400V, 410V can be customized if other voltages are needed.

1. What is your payment terms?

TT.

40% T/T deposit, 60% balance be paid before loading after good ready.

2. What is your delivery time?

Within 10 business days after your paying.

3. What is your power supply?

It will depend on your local power supply and we will adjust for you.

4. What is your minimum order quantity?

One set.

5. Are the all labels and instructions English?

Yes. Our labels, instructions and control system are all English.

6. How long of the guarantee?

Three years. 

Hot Tags: PLC Hydraulic Copper Busbar bending cutting punching Processing Machine, suppliers, manufacturers, first price, OEM factory, for sale, Copper Bar Square Hole Dies, Bending Copper Busbar, 3 in 1 Busbar Machine, Mobile Busbar Processing Machine, Copper Bar Processing Machine, Copper Punching Machine